Pratama A12.2018.06001

SETTING VLAN 1

Switch#conf t
Switch(config)#vlan 50
Switch(config-vlan)#name pratama
Switch(config-vlan)#exit
Switch(config)#vlan 60
Switch(config-vlan)#name ali
Switch(config-vlan)#exit
Switch(config)#int fa 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa 0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa 0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 60
Switch(config-if)#exit
Switch(config)#int fa 0/5
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 60


Switch>ena
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/1
Switch(config-if)#s
Switch(config-if)#sw
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch>en
Switch#conf t
Switch(config)#vlan 50
Switch(config-vlan)#name pratama
Switch(config-vlan)#ex
Switch(config)#vlan 60
Switch(config-vlan)#name ali
Switch(config-vlan)#ex
Switch(config)#int fa0/5
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 50
Switch(config-if)#ex
Switch(config)#int fa0/6
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 50
Switch(config-if)#ex
Switch(config)#int fa0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 60
Switch(config-if)#ex
Switch(config)#int fa0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 60
Switch(config-if)#ex


Switch>ena
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/1
Switch(config-if)#s
Switch(config-if)#sw
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int gig0/0
Router(config-if)#ip add 192.68.20.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int gi 0/1
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router(config-if)#ex
Router(config)#int gig0/1.50
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1.50, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1.50, changed state to up

Router(config-subif)#en
Router(config-subif)#encapsulation dot
Router(config-subif)#encapsulation dot1Q 50
Router(config-subif)#ip add 192.168.50.129 255.255.255.128
Router(config-subif)#ex
Router(config)#int gig 0/1.60
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1.60, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1.60, changed state to up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 60
Router(config-subif)#ip add 192.168.60.65 255.255.255.192
Router(config-subif)#ex

Alat dan Bahan
1. Laptop
2. Internet
3. Mikrotik
4. Kabel RJ


Tahap pelaksanaan :


1. Buka winbox,




2. refresh untuk mendapatkan mac address secara otomatis dan connect




3. Lakukan reset konfigurasi soft reset dengan cara :

• klik system > reset configuration > centang no default > yes

pilih yes



Klik new terminal dan ketik ip sesuai dengan yang absen dan ip yang sudah ditentukan

ip <> address<>add<>address=10.10.20.29/24<>interface=ether1<>disabled=no>enter
ip <> address<>add<>address=192.168.100.1/24<>interface=ether2<>disabled=no>enter
ip <> address<>add<>address=192.168.200.1/24<>interface=ether3<>disabled=no>enter


ip address print
    ether1 : 10.10.20.29/24
    ether2 : 192.168.100.1/24
    ether3 : 192.168.200.1/24



2. Setting Gateway

 Ketikan : ip<>route<>add<>gateway=10.10.20.1




3. Setting DNS

 Ketikan : ip<>dns<>set<>servers=10.10.20.1<>allow-remote-request=yes



ping google.com



4. Setting NAT




Selanjutnya ping 8.8.8.8




Screenshoot ping google.com dan blog saya




5. Setting DHCP server

Selanjutnya kita buat dhcp pada Ether 3 caranya ip<>dhcp-server<>setup> enter






6. Setting Proxy

ketikkan perintah ip<>proxy<>set<>enabled=yes<>cache-administrator=Pratama_29_XIITKJ2<>cache-on-disk=yes >enter










3.mkv